Plenty inventory of slurry pump parts. Not only for the below shown rubber liners, but also for metal pump parts such as impellers, volute liners, and so on. 

What we can guarantee is a swift delivery to minimize the customers' down time. 

If the Slurry Pump is found to be blocked during use, how to solve it is that many customers think that this is a relatively complicated problem. Once this blockage problem is not handled properly, it will easily cause damage to the equipment, thereby affecting the efficiency of use. Therefore, everyone should pay special attention to the clogging problem of the slurry pump. In fact, if you grasp the following points, you can easily solve the problem.

(1) The solid and hard deposits in the volute of the horizontal slurry pump make it silted up, and measures to remove the silt can be taken.

(2) If the axis of the shaft and the feeding box are different, the main reason is that the machining error is large and the installation is incorrect. Care should be taken to check that the installation is correct after installation. If the sealing water ring is seriously worn, it needs to be replaced with a new water ring. If the sealing water pipe is blocked, the sealing water cannot enter the middle of the packing, which will cause the packing to wear quickly and lead to leakage. The blocked water pipe should be dredged to keep the sealing water clean.

(3) If the impeller or the water inlet and outlet pipelines are blocked, the impeller or pipeline can be cleaned. If the impeller is seriously worn, it should be replaced. If the packing port leaks, the packing should be pressed tightly. If the conveying height is too high, the loss resistance in the pipe is too large, so reduce the conveying height or reduce the resistance.

The horizontal slurry pump should be regularly maintained during its use, including dredging. This can effectively avoid the problem of slurry pump blockage. If you encounter these problems in the later use of the slurry pump, you can follow the steps above. resolve.

Today we will take a look at the froth pump will encounter what kind of problems, encounter these problems, we should do?

First of all, one of our common problems is that the shaft power of the froth pump is too large, which will cause friction in the foam pump, misalignment or imbalance between the motor shaft and the pump shaft, which will also lead to bearing damage, excessive flow of the froht pump, and too tight belt of the driving device.

At this time, the corresponding solution is to eliminate friction, adjust the motor shaft and pump shaft, replace the new bearing, adjust the running condition of the foam pump, adjust the belt, so that the above problems will be solved.

froth pump also often encounter the problem is that the bearing of the froht pump is overheating, the bearing is easy to damage, replace the new bearing, the bearing grease of the froth pump is too much or too little, add grease to be appropriate, there is debris in the grease, replace the new grease.

The bearing life of the froth pump is too short, the motor end and the pump shaft are not aligned or uneven phenomenon occurs, the motor shaft and the pump shaft can be adjusted, the shaft of the froth pump is bent, it is necessary to replace the new pump shaft, the friction in the froth pump or the impeller is out of balance, we need to eliminate the friction, and then replace the new impeller. When there are foreign bodies in the bearing of the froth pump or improper grease, we can clean the shaft.

The impeller of slurry pump is an important part in the slurry pump. The slurry transportation depends on the centrifugal force generated by the high-speed rotation of the impeller. To the slurry pump accessories wear the fastest is also the impeller, so we want to replace the wear of the impeller, how to remove the impeller.

CNSME gives you an introduction.

The impeller of our slurry pump is usually buckled, which is opposite to the direction of rotation of the pump. From the direction of the pump inlet, the direction of rotation of the pump is counterclockwise rotation, so when the pump starts, the impeller will turn tighter. So if you want to remove the impeller, you need to jam the pump shaft with calipers, and then rotate according to the direction of rotation of the pump. Because the pump runs for a period of time, the impeller will be relatively tight, so when it is removed if it does not move, you can take a crowbar to knock a few times and try again.

Large pump will have impeller removal ring, then need to remove the removal ring, and then rotate the impeller.

If you have slurry pump, foam pump and other questions can contact our company, we have professional technology for you to answer online!

CNSME PUMP's website has been fully revamped and is now officially live! In addition to upgrading the website, we have also refreshed our company logo, presenting a more modern and professional brand image. As a leading supplier of slurry pumps and spare parts, CNSME PUMP is dedicated to providing efficient, durable pump products and customized solutions for global customers. Whether in mining, metallurgy, power plants, or other heavy industries, we offer high-quality pump equipment and accessories to support your needs. Visit our website to learn more and join us as we embark on an even brighter future!