During operation, there are four types of common failures of
slurry pumps
: corrosion and abrasion, mechanical failure, performance failure and shaft sealing failure. These four types of failures often affect each other.


For example, the corrosion and abrasion of the impeller will cause performance failure and mechanical failure, and the damage of the shaft seal will also cause performance failure and mechanical failure.


1. Bearings Overheated


A. Too much, too little or deterioration of lubricating grease/oil will cause the bearing to heat up, and the appropriate amount and quality of oil should be adjusted.


B. Check whether the pump -motor unit is concentric, adjust the pump and aglign it with the motor.


C. If the vibration is abnormal, check whether the rotor is balanced.


2. Reasons and solutions that may causenon output of slurry


A. There is still air in the suction pipe or pump, which should be filled with liquid to discharge the air.


B. The valves on the inlet and outlet pipeline are closed or the blind plate is not removed, then the valve should be opened and the blind plate removed.


C. The actual head is higher than the maximum head of the pump, a pump with higher head should be employed


D. The rotation direction of the impeller is wrong, so the rotation direction of the motor should be corrected.


E. The lifting height is too high, which should be lowered, and the pressure at the inlet should be increased.


F. The debris is blocked the pipe or the suction pipeline is small, the blockage should be removed and the pipe diameter should be enlarged.


G. The speed does not match, which should be adjusted to meet the requirements.


3. Reasons and solutions for insufficient flow and head


A. The impeller is damaged, replace it with a new impeller.


B. Too much damage to the sealing ring, replace the sealing ring.


C. The inlet and outlet valves are not fully opened, they should be fully opened.


D. The density of the medium does not meet the requirements of the pump, re-calculate it.


4. Reasons for serious seal leakage and solutions


A. Improper selection of sealing element materials, replace suitable elements.


B. Serious wear, replace the worn parts and adjust the spring pressure.


C. If the O-ring is damaged, replace the O-ring.


5. Reasons and solutions of motor overload


A. The pump and engine (output end of the motor or diesel engine) are not aligned, adjust the position so that the two are aligned.


B. The relative density of the medium becomes larger, change the operating conditions or replace the motor with suitable power.


C. Friction occurs in the rotating part, repair the friction part.


D. The resistance (such as pipeline friction loss) of the device is low, and the flow will become bigger than required. The drain valve should be closed to obtain the flow rate specified on the pump label.

If the
Slurry Pump
is found to be blocked during use, how to solve it is that many customers think that this is a relatively complicated problem. Once this blockage problem is not handled properly, it will easily cause damage to the equipment, thereby affecting the efficiency of use. Therefore, everyone should pay special attention to the clogging problem of the slurry pump. In fact, if you grasp the following points, you can easily solve the problem.


(1) The solid and hard deposits in the volute of the horizontal slurry pump make it silted up, and measures to remove the silt can be taken.


(2) If the axis of the shaft and the feeding box are different, the main reason is that the machining error is large and the installation is incorrect. Care should be taken to check that the installation is correct after installation. If the sealing water ring is seriously worn, it needs to be replaced with a new water ring. If the sealing water pipe is blocked, the sealing water cannot enter the middle of the packing, which will cause the packing to wear quickly and lead to leakage. The blocked water pipe should be dredged to keep the sealing water clean.


(3) If the impeller or the water inlet and outlet pipelines are blocked, the impeller or pipeline can be cleaned. If the impeller is seriously worn, it should be replaced. If the packing port leaks, the packing should be pressed tightly. If the conveying height is too high, the loss resistance in the pipe is too large, so reduce the conveying height or reduce the resistance.


El
horizontal slurry pump
should be regularly maintained during its use, including dredging. This can effectively avoid the problem of slurry pump blockage. If you encounter these problems in the later use of the slurry pump, you can follow the steps above. resolve.

The first batch of slurry pump model has been produced, and the new and old customers who need it (those who have business dealings with our company) can contact the company's sales and get the slurry pump model they want.



CNSME is a professional slurry pump manufacturer, we offer all types of slurry pumps, horizontal slurry pumps, vertical slurry pumps, centrifugal slurry pumps, sand and gravel pumps, foam pumps, vertical foam pumps and matching slurry pump spare parts

China's slurry pump suppliers will participate in MiningWorld Russia, a mining and mining machinery and equipment exhibition held in Russia from April 23 to April 25,Our booth number is C5021.

CNSME Pump, a professional manufacturer and supplier of slurry pumps, is honored to announce our participation in the 2024 Chile Mining Exhibition (EXPONOR CHILE). Our booth is now fully set up, and we sincerely invite industry professionals to visit us.



The 2024 Chile Mining Exhibition will be held from June 3 to June 6 in Atacama Desert, Antofagasta, Chile. This exhibition is one of the most significant events in the global mining industry, bringing together mining companies, suppliers, and experts from around the world, providing a platform to showcase innovative technologies and products.


Our booth number is 221, located in the central area of the exhibition hall. Although the booth size this year limits our ability to fully display all our products, we have prepared detailed product brochures and arranged for professional staff to provide on-site explanations. Here, you will have the opportunity to:


CNSME Pump always adheres to the philosophy of "innovation-driven, service-oriented," committed to providing high-quality mining solutions to customers worldwide. Despite the limited booth space this year, we still look forward to face-to-face interactions, sharing our innovative products and technologies with you.


We sincerely invite you to visit our booth and experience the professionalism and enthusiasm of CNSME Pump. We look forward to meeting you at the exhibition!


Thank you for your attention and support for CNSME Pump. We look forward to your visit!